geda
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
geda [2013/05/16 07:32] – [PCB Tips] samtod | geda [2015/05/08 12:48] – [Create Footprint] lzufferey | ||
---|---|---|---|
Line 16: | Line 16: | ||
-- copy gschemrc to gnetlistrc | -- copy gschemrc to gnetlistrc | ||
+ | For more information visit : [[http:// | ||
===== Create Symbol ===== | ===== Create Symbol ===== | ||
Line 179: | Line 180: | ||
+ | For more information, | ||
===== Schematic to PCB ===== | ===== Schematic to PCB ===== | ||
Line 195: | Line 197: | ||
- If there isn't any error, you can start your PCB. | - If there isn't any error, you can start your PCB. | ||
+ | |||
+ | If the first solution does not work, try this: | ||
+ | |||
+ | - Open the terminal | ||
+ | - cd / | ||
+ | - gsch2pcb -d / | ||
+ | - Now, a new file was created on your folder (YOUR_SCHEMATIC.pcb) | ||
+ | - Run the .pcb and it's done | ||
+ | |||
+ | Sometimes, the netlist does not load: | ||
+ | - In the .pcb, select **File-> | ||
+ | - Search in your folder the .net | ||
+ | - Type o to optimise rat | ||
+ | - You can start route | ||
===== Import the board on PCB ===== | ===== Import the board on PCB ===== | ||
Line 340: | Line 356: | ||
{{: | {{: | ||
- | To search all tracks pins and pads connected | + | If you want to replace |
- | If you want to see the bottom | + | There' |
- | If you want to replace the " | + | * **1 to 9 => change layer** |
+ | * **F1 to F11 => Tool selection (all description in PCB Tips)** | ||
+ | * del => delete component, track, via, etc at the cursor location | ||
+ | * shift+del => delete selected objects | ||
+ | * **u => undo operation** | ||
+ | * **shift+r => redo operation** | ||
+ | * m => move our track on the selected layer | ||
+ | * shift+m => move selected object on the selected layer | ||
+ | * **b => change a component | ||
+ | * shift+b => change all component selected between | ||
+ | * z & shift+z => Zoom | ||
+ | * v => zoom out completely | ||
+ | * **tab => switch the side of the view** | ||
+ | * **n => edit all kind of text** | ||
+ | * h => show/hide component name | ||
+ | * d => show/hide the number/name of pin/via | ||
+ | * **f => highlight selected connection** | ||
+ | * shift+f => reset all highlight connection | ||
+ | * i => open library window | ||
+ | * : => open user command | ||
+ | * s & shift+s => change the width of lines, arcs, text objects, pins,pads and vias at the cursor location | ||
+ | * l & shift+l => change the width of our track while routing | ||
+ | * / =>change the routing style: none, _ /, \ _ | ||
+ | * g & maj+g => add or subtract 5mils to the grid | ||
+ | * ctrl+g & maj+ctrl+g => add or subract 0.05mm to the grid | ||
+ | * maj+v & maj+ctrl+v =>add or subtract 5mil to default via size | ||
+ | * alt+v & maj+alt+v =>add or subtract 5mil to default via drill | ||
+ | * **o => acualise and optimize all rats** | ||
+ | * **q => make a line/pad rectangular** | ||
+ | * k => increase the size of the clearance of a track | ||
+ | * shift+k => decrease the size of the clearance of a track | ||
- | When you replace a component you must press "O" | + | =====Plan de masse===== |
+ | |||
+ | Pour pouvoir créer un plan de masse ou de VCC, il suffit de tracer un rectangle. | ||
+ | |||
+ | En utilisant l' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Pour connecter directement une piste au plan, il faut décocher la case "**New lines, arcs clear polygons**" | ||
+ | |||
+ | **Attention: | ||
=====Create a build of material from shematics===== | =====Create a build of material from shematics===== | ||
Line 360: | Line 416: | ||
* vi attribs : then press i to go in insertion mode | * vi attribs : then press i to go in insertion mode | ||
* and write the " | * and write the " | ||
- | * when you finish presse enter, ESC, :wq **use to get out of vi attribs** | + | * when you finish presse enter, ESC and write :wq **use to get out of vi attribs** |
- | * gnetlist -g bom -o bom.txt NiX1-V1-MB.sch | + | * gnetlist -g bom -o bom.txt NiX1-V1-MB.sch |
* Your build of material is created | * Your build of material is created | ||
Line 372: | Line 428: | ||
<note important> | <note important> | ||
+ | |||
+ | =====Create a .zip with the terminal===== | ||
+ | |||
+ | * Open your terminal | ||
+ | * cd / | ||
+ | * $ 7z a -tzip Projectfile.zip . | ||
+ | |||
+ | |||
=====Create a screen of your PCB===== | =====Create a screen of your PCB===== | ||
Line 399: | Line 463: | ||
Links : | Links : | ||
- | http:// | + | * http:// |
- | http:// | + | |
- | http:// | + | |
- | There' | + | There' |
You can use a script to be faster with Gnucap. Write on gedit the command you want use in the options of Gnucap. For example : | You can use a script to be faster with Gnucap. Write on gedit the command you want use in the options of Gnucap. For example : | ||
Line 414: | Line 478: | ||
* ~ gwave simulation.out | * ~ gwave simulation.out | ||
+ | If you want to have a simulation who looks better use Gnuplot : | ||
+ | After you have made the simulation write in the terminal : | ||
+ | |||
+ | * Gnuplot (You enter in the options of Gnuplot) | ||
+ | * set xlabel "What you want" | ||
+ | * set ylabel "What you want" | ||
+ | * plot ' | ||
+ | |||
+ | There' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | With the right-click you can do a measure easily. | ||
===== Q/A ===== | ===== Q/A ===== | ||
To add input/ | To add input/ | ||
Line 426: | Line 503: | ||
<note warning> | <note warning> | ||
+ | |||
+ | ==== gschem2pcb with command line ==== | ||
+ | |||
+ | gsch2pcb EdgeBoard_DS18B20.sch --elements-dir ../ | ||
Line 431: | Line 512: | ||
==== Links ===== | ==== Links ===== | ||
* http:// | * http:// | ||
+ | * http:// | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
Line 440: | Line 522: | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
+ | * http:// | ||
+ | * http:// | ||
+ | * http:// |
geda.txt · Last modified: 2019/08/29 12:04 by maferreira