| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| acdsn:acdsn-ic-fx [2015/07/13 13:56] – Change delay and sample rate in seconds fdacruz | acdsn:acdsn-ic-fx [2018/05/28 07:21] (current) – aheritier |
|---|
| | delete thermochron | k | <sid> || | | delete thermochron | k | <sid> || |
| | restart | s ||| | | restart | s ||| |
| | | delete tmp files | y || delete file for Newfile fct | |
| |
| ==== New ==== | ==== New ==== |
| | new discontinuation | d | <discontinuation> | set the timeout value after which the slave consider itself to be abandoned by the server (in sec) | | | new discontinuation | d | <discontinuation> | set the timeout value after which the slave consider itself to be abandoned by the server (in sec) | |
| | new entry | e | <comptability> | count number of lines in ACCESS file, update log_position and set compatibility | | | new entry | e | <comptability> | count number of lines in ACCESS file, update log_position and set compatibility | |
| | new file | g |%%<filename>%%\t<>\t<CRC> || | | new file | g |%%<filename>%%\t<CRC> || |
| | new buzzer | j | <mode> | buzzer activated or not | | | new buzzer | j | <mode> | buzzer activated or not | |
| | new thermochron | k | <sid>\t<id_profile>\t<suid> || | | new thermochron | k | <sid>\t<id_profile>\t<suid> || |
| | new mode | m | <mode> | NiX1 enable/disable | | | new mode | m | <mode> | NiX1 enable/disable | |
| | query firmware version | n | %%<filename>%%\t<CRC>\t<retry times> || | | query firmware version | n | %%<filename>%%\t<CRC>\t<retry times> || |
| | new profile | p | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate> | change profile | | | new profile | p | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate>\t<manual_mode>\t<rollover> | change profile | |
| | new general status | s | <value> | set value in NiX general status | | | new general status | s | <value> | set value in NiX general status | |
| | new timestamp | t | <timestamp> | only if RTC defined (used to synchronize clock)(date +%s) | | | new timestamp | t | <timestamp> | only if RTC defined (used to synchronize clock)(date +%s) | |
| | new overdrive speed | v | <device>\t<mode> | put 1-wire devices in overdrive speed | | | new overdrive speed | v | <2>\t<mode> | put 1-wire device 2 in overdrive speed | |
| | | new file packet | y | <nbrPacket>/t<blockLength>/t<CRC>/t<block> || |
| | new baudrate | z | <baudrate> || | | new baudrate | z | <baudrate> || |
| ==== Query ==== | ==== Query ==== |
| | query general status | s || how many missions recorded since last query | | | query general status | s || how many missions recorded since last query | |
| | query timestamp | t || only if RTC is defined | | | query timestamp | t || only if RTC is defined | |
| | query overdrive speed | v |%%<1|2>%%|| | | query overdrive speed | v |%%<2>%%|| |
| ===== Options ===== | ===== Options ===== |
| ^ Options ^ Comments ^ | ^ Options ^ Comments ^ |
| | |<block> | block content (each char is formatted in 2 ascii in hexa value) => 'a' = 0x61 => sent : "61" | |
| | |<blockLength> | length of the actual block in bytes | |
| |<comptability> | 0 to 65534 How many access we would like receive | | |<comptability> | 0 to 65534 How many access we would like receive | |
| | |<CRC> | 16 bits value | |
| |<delay> | 0 to 65535 How many minutes the device waits before starting logging process | | |<delay> | 0 to 65535 How many minutes the device waits before starting logging process | |
| |<discontinuation> | 0 to 4294967295 (if 0 we don't care about discontinuation) | | |<discontinuation> | 0 to 4294967295 (if 0 we don't care about discontinuation) | |
| |<limitH> | -40. to +85. Higher alarm limit (°C) | | |<limitH> | -40. to +85. Higher alarm limit (°C) | |
| |<limitL> | -40. to +85. Lower alarm limit (°C) | | |<limitL> | -40. to +85. Lower alarm limit (°C) | |
| | |<nbrPacket> | packet total number for a file | |
| | |<manual_mode> | choose if a new mission start automatically (0) or manually (1) after discharging | |
| |<mode> | 0 [disable] or 1 [enable] | | |<mode> | 0 [disable] or 1 [enable] | |
| |<rate> | 0 to 255 how many minutes the temperature conversions are apart from each other during a mission| | |<rate> | 0 to 255 how many minutes the temperature conversions are apart from each other during a mission| |
| | |<rollover> | choose if the mission is in rollover mode (1) or not (0) | |
| |<sid> | SID of the iButton (in iControl case family 21) | | |<sid> | SID of the iButton (in iControl case family 21) | |
| |<suid> | identification of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009 | | |<suid> | identification of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009 | |
| LOCK_0 0 | LOCK_0 0 |
| LOCK_1 0 | LOCK_1 0 |
| OD_SPEED_0 0 | |
| OD_SPEED_1 0 | OD_SPEED_1 0 |
| VALID_ACCESS_TIMEOUT 5 | VALID_ACCESS_TIMEOUT 5 |
| DELAY 300 | DELAY 300 |
| SAMPLE_RATE 120 | SAMPLE_RATE 120 |
| | MANUAL_MODE 1 |
| | ROLLOVER 0 |
| </file> | </file> |
| |
| DELAY 3932100 | DELAY 3932100 |
| SAMPLE_RATE 960 | SAMPLE_RATE 960 |
| | MANUAL_MODE 0 |
| | ROLLOVER 1 |
| </file> | </file> |
| |
| NiX1 Timestamp (YYYY-MM-DD): 2014-08-04T10:02:12 | NiX1 Timestamp (YYYY-MM-DD): 2014-08-04T10:02:12 |
| Thermochron Timestamp (YYYY-MM-DD): 2014-08-04T10:02:11 | Thermochron Timestamp (YYYY-MM-DD): 2014-08-04T10:02:11 |
| Delay (min): 25 | Delay (sec): 1500 |
| Alarm High Temperature (°C): 28.5 | Alarm High Temperature (°C): 28.5 |
| Alarm Low Temperature (°C): 0.5 | Alarm Low Temperature (°C): 0.5 |
| Sample Rate (min): 2 | Sample Rate (sec): 180 |
| | Enable Mission: 1 |
| | Rollover: 0 |
| Mission Samples Counter: 4166 | Mission Samples Counter: 4166 |
| Device Samples Counter: 135257 | Device Samples Counter: 135257 |
