Differences

This shows you the differences between two versions of the page.

--- acdsn:acdsn-sc-fx [2015/07/09 09:06] – Change arguments and options fdacruz
+++ acdsn:acdsn-sc-fx [2018/05/28 07:19] (current) – aheritier
@@ Line 26: / Line 26: @@
 | restart              | s         |||
 | delete wire          | w         | <sid> | address of device to delete|
+| delete tmp files  | y         || delete file for Newfile fct |
 ==== New ====
 ^ Label                    ^ Arguments ^ Options                   ^ Comments ^
 | new alarm status	   | a         | <value>                   | set the alarm value |
 | new discontinuation	   | d         | <discontinuation>         | set the timeout value after which the slave consider itself to be abandoned by the server|
-| new file                 | g         |%%<filename>%%\t<>\t<CRC>  ||
+| new file                 | g         |%%<filename>%%\t<CRC>  ||
 | new buzzer mode          | j         | <mode>                    | buzzer activated or not |
 | new limit                | l         | <sid>\t<limitL>\t<limitH>\t<resolution> | set alarm boundaries |
@@ Line 37: / Line 38: @@
 | new recess               | r         | <recess>                  | scan-rate interval |
 | new general status       | s         | <value>                   | set value in NiX general status |
-| new timestamp            | t         | <timestamp>         | only if RTC defined (used to synchronize clock) |
+| new timestamp            | t         | <timestamp>\t<TZ>         | only if RTC defined (used to synchronize clock) |
 | new wire                 | w         | 0                         | scan the lines and return the number of OW device found |
 | :::                      | :::       | <sid>\t<suid>\t<mode>   | add an OW device to the desired address (only families 20 and 28)|
+| new file packet          | y         | <nbrPacket>/t<blockLength>/t<CRC>/t<block>                ||
 | new baudrate             | z         | <baudrate>                ||
 ==== Query ====
@@ Line 57: / Line 59: @@
 ===== Options =====
 ^ Options               ^ Comments ^
+|<block>                | block content (each char is formatted in 2 ascii in hexa value) => 'a' = 0x61 => sent : "61"             |
+|<blockLength>          | length of the actual block in bytes              |
+|<CRC>                  | 16 bits value                                    |
 |<discontinuation>      | 0 to 4294967295 [seconds] (if 0 we don't care about discontinuation) |
+|%%<filename>%%         | File on uSD: CONFIG.TXT, KEYS.TXT ...            |
 |<limitH>               | Higher alarm limit (integer from -128 to +127) |
 |<limitL>               | Lower alarm limit (integer from -128 to +127) |
+|<nbrPacket>            | packet total number for a file                   |
 |<mode>                 | 0 [disable] or 1 [enable]                   |
 |<recess>               | 0 to 65534 [seconds] (~18H) (if 0 we don't care about check sensors alarms) |
@@ Line 65: / Line 72: @@
 |<suid>                 | alias of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009 |
 |<timestamp>            | 0 to 9'999'999'999 [seconds since 1.1.1970] |
+|<timezone>             | -1200 to +1400 |
+===== Return Code (HEX) =====
+^ Code ^ Transmission ^ Functions ^
+|  67  | ERROR_OPEN            | |
+|  68  | ERROR_SHORTGND           | |
+|  69  | ERROR_SHORTVCC           | |
 ===== Configuration Files (Micro-SD) =====