Differences

This shows you the differences between two versions of the page.

--- acdsn:acdsn-ic-fx [2015/07/09 07:32] – Changes in micro-sd files fdacruz
+++ acdsn:acdsn-ic-fx [2015/08/05 09:25] – delete overdrive speed OW_O fdacruz
@@ Line 31: / Line 31: @@
 | new valid access timeout | c         | <timeout>                 ||
 | new discontinuation	   | d         | <discontinuation>         | set the timeout value after which the slave consider itself to be abandoned by the server (in sec) |
+| new entry                | e         | <comptability>            | count number of lines in ACCESS file, update log_position and set compatibility |
 | new file                 | g         |%%<filename>%%\t<>\t<CRC>  ||
 | new buzzer               | j         | <mode>                    | buzzer activated or not |
@@ Line 37: / Line 38: @@
 | new mode                 | m         | <mode>                    | NiX1 enable/disable |
 | query firmware version   | n         | %%<filename>%%\t<CRC>\t<retry times> ||
-| new profile              | p         | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate> | change profile |
+| new profile              | p         | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate>\t<manual_mode>\t<rollover> | change profile |
-| new status               | s         | <comptability>            | count number of lines in ACCESS file, update log_position and set comptability |
+| new general status       | s         | <value>                   | set value in NiX general status |
 | new timestamp            | t         | <timestamp>               | only if RTC defined (used to synchronize clock)(date +%s) |
-| new overdrive speed      | v         | <device>\t<mode>          | put 1-wire devices in overdrive speed |
+| new overdrive speed      | v         | <2>\t<mode>               | put 1-wire device 2 in overdrive speed |
 | new baudrate             | z         | <baudrate>                ||
 ==== Query ====
 ^ Label                        ^ Arguments ^ Options ^ Comments ^
-| query general status         | a         |||
 | query bad access timeout     | b         |||
 | query valid access timeout   | c         |||
@@ Line 55: / Line 55: @@
 | query mode                   | m         || NiX1 active or not |
 | query firmware version       | n         |||
-| query status                 | s         || how many missions recorded since last query |
+| query general status         | s         || how many missions recorded since last query |
 | query timestamp              | t         || only if RTC is defined |
-| query overdrive speed        | v         |%%<1|2>%%||
+| query overdrive speed        | v         |%%<2>%%||
 ===== Options =====
 ^ Options          ^ Comments                                                                     ^
-|<address>         | 0 to 65535                                                                   |
 |<comptability>    | 0 to 65534 How many access we would like receive                             |
 |<delay>           | 0 to 65535 How many minutes the device waits before starting logging process |
@@ Line 66: / Line 65: @@
 |%%<filename>%%    | File on uSD: CONFIG.TXT, KEYS.TXT ...                                        |
 |<id_profile>      | identification of profile on 8 char ['0-9'-'A-Z'-'a-z'] like 0B0a0001        |
-|<limit>           | Max line to display                                                          |
+|<limit>           | Max line to display [0=all lines]                |
 |<limitH>          | -40. to +85. Higher alarm limit (°C)                                         |
 |<limitL>          | -40. to +85. Lower alarm limit (°C)                                          |
+|<manual_mode>     | choose if a new mission start automatically (0) or manually (1) after discharging |
 |<mode>            | 0 [disable] or 1 [enable]                                                    |
 |<rate>            | 0 to 255 how many minutes the temperature conversions are apart from each other during a mission|
+|<rollover>        | choose if the mission is in rollover mode (1) or not (0)                     |
 |<sid>             | SID of the iButton (in iControl case family 21)                              |
 |<suid>            | identification of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009        |
@@ Line 84: / Line 85: @@
 <file txt CONFIG.TXT>
-ADDRESS	1
 BAD_ACCESS_TIMEOUT	5
 BAUDRATE	9600
@@ Line 92: / Line 92: @@
 LOCK_0	0
 LOCK_1	0
-OD_SPEED_0	0
 OD_SPEED_1	0
 VALID_ACCESS_TIMEOUT	5
@@ Line 114: / Line 113: @@
 ==== Profiles Files====
-These files contain the parameters to launch a mission.
+These files contain the parameters to launch a mission. Delay and sample rate are in seconds.
 <file txt 000A0001.TXT>
 ALARM_HIGH_TEMPERATURE	85
 ALARM_LOW_TEMPERATURE	-13.5
-DELAY	5
+DELAY	300
-SAMPLE_RATE	2
+SAMPLE_RATE	120
+MANUAL_MODE	1
+ROLLOVER	0
 </file>
@@ Line 126: / Line 127: @@
 ALARM_HIGH_TEMPERATURE	12.5
 ALARM_LOW_TEMPERATURE	-3.5
-DELAY	65535
+DELAY	3932100
-SAMPLE_RATE	16
+SAMPLE_RATE	960
+MANUAL_MODE	0
+ROLLOVER	1
 </file>
@@ Line 207: / Line 210: @@
 NiX1 Timestamp (YYYY-MM-DD):        2014-08-04T10:02:12
 Thermochron Timestamp (YYYY-MM-DD): 2014-08-04T10:02:11
-Delay (min): 25
+Delay (sec): 1500
 Alarm High Temperature (°C): 28.5
 Alarm Low  Temperature (°C):  0.5
-Sample Rate (min): 2
+Sample Rate (sec): 180
+Enable Mission: 1
+Rollover: 0
 Mission Samples Counter: 4166
 Device Samples Counter: 135257