Differences

This shows you the differences between two versions of the page.

--- acdsn:acdsn-ic-fx [2015/07/13 13:56] – Change delay and sample rate in seconds fdacruz
+++ acdsn:acdsn-ic-fx [2015/08/05 09:25] – delete overdrive speed OW_O fdacruz
@@ Line 38: / Line 38: @@
 | new mode                 | m         | <mode>                    | NiX1 enable/disable |
 | query firmware version   | n         | %%<filename>%%\t<CRC>\t<retry times> ||
-| new profile              | p         | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate> | change profile |
+| new profile              | p         | <id_profile>\t<limitL>\t<limitH>\t<delay>\t<rate>\t<manual_mode>\t<rollover> | change profile |
 | new general status       | s         | <value>                   | set value in NiX general status |
 | new timestamp            | t         | <timestamp>               | only if RTC defined (used to synchronize clock)(date +%s) |
-| new overdrive speed      | v         | <device>\t<mode>          | put 1-wire devices in overdrive speed |
+| new overdrive speed      | v         | <2>\t<mode>               | put 1-wire device 2 in overdrive speed |
 | new baudrate             | z         | <baudrate>                ||
 ==== Query ====
@@ Line 57: / Line 57: @@
 | query general status         | s         || how many missions recorded since last query |
 | query timestamp              | t         || only if RTC is defined |
-| query overdrive speed        | v         |%%<1|2>%%||
+| query overdrive speed        | v         |%%<2>%%||
 ===== Options =====
 ^ Options          ^ Comments                                                                     ^
@@ Line 68: / Line 68: @@
 |<limitH>          | -40. to +85. Higher alarm limit (°C)                                         |
 |<limitL>          | -40. to +85. Lower alarm limit (°C)                                          |
+|<manual_mode>     | choose if a new mission start automatically (0) or manually (1) after discharging |
 |<mode>            | 0 [disable] or 1 [enable]                                                    |
 |<rate>            | 0 to 255 how many minutes the temperature conversions are apart from each other during a mission|
+|<rollover>        | choose if the mission is in rollover mode (1) or not (0)                     |
 |<sid>             | SID of the iButton (in iControl case family 21)                              |
 |<suid>            | identification of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009        |
@@ Line 90: / Line 92: @@
 LOCK_0	0
 LOCK_1	0
-OD_SPEED_0	0
 OD_SPEED_1	0
 VALID_ACCESS_TIMEOUT	5
@@ Line 119: / Line 120: @@
 DELAY	300
 SAMPLE_RATE	120
+MANUAL_MODE	1
+ROLLOVER	0
 </file>
@@ Line 126: / Line 129: @@
 DELAY	3932100
 SAMPLE_RATE	960
+MANUAL_MODE	0
+ROLLOVER	1
 </file>
@@ Line 205: / Line 210: @@
 NiX1 Timestamp (YYYY-MM-DD):        2014-08-04T10:02:12
 Thermochron Timestamp (YYYY-MM-DD): 2014-08-04T10:02:11
-Delay (min): 25
+Delay (sec): 1500
 Alarm High Temperature (°C): 28.5
 Alarm Low  Temperature (°C):  0.5
-Sample Rate (min): 2
+Sample Rate (sec): 180
+Enable Mission: 1
+Rollover: 0
 Mission Samples Counter: 4166
 Device Samples Counter: 135257