Differences

This shows you the differences between two versions of the page.

--- acdsn:acdsn-sc-fx [2015/07/08 09:13] – [New] fdacruz
+++ acdsn:acdsn-sc-fx [2018/04/19 12:08] – aheritier
@@ Line 28: / Line 28: @@
 ==== New ====
 ^ Label                    ^ Arguments ^ Options                   ^ Comments ^
+| new alarm status	   | a         | <value>                   | set the alarm value |
 | new discontinuation	   | d         | <discontinuation>         | set the timeout value after which the slave consider itself to be abandoned by the server|
 | new file                 | g         |%%<filename>%%\t<>\t<CRC>  ||
@@ Line 34: / Line 35: @@
 | new mode                 | m         | <mode>                    | NiX1 enable/disable |
 | new firmware             | n         | %%<filename>%%\t<CRC>\t<retry times> ||
 | new recess               | r         | <recess>                  | scan-rate interval |
-| new timestamp            | t         | <timestamp>         | only if RTC defined (used to synchronize clock) |
+| new general status       | s         | <value>                   | set value in NiX general status |
+| new timestamp            | t         | <timestamp>\t<TZ>         | only if RTC defined (used to synchronize clock) |
 | new wire                 | w         | 0                         | scan the lines and return the number of OW device found |
 | :::                      | :::       | <sid>\t<suid>\t<mode>   | add an OW device to the desired address (only families 20 and 28)|
+| new baudrate             | z         | <baudrate>                ||
 ==== Query ====
 ^ Label                        ^ Arguments ^ Options ^ Comments                     ^
+| query alarm status	       | a         || number of sensors in alarm |
 | query discontinuation status | d         || no query from server timeout |
 | query file                   | g         | %%<filename>%%\t<limit> ||
@@ Line 47: / Line 51: @@
 | query firmware version       | n         |||
 | query recess                 | r         || scan-rate intervall          |
-| query status                 | s         || how many devices in alarm |
+| query general status         | s         |||
 | query timestamp              | t         || only if RTC is defined       |
 | query value                  | x         | <sid> | give the temperature of the device |
@@ Line 53: / Line 57: @@
 ===== Options =====
 ^ Options               ^ Comments ^
+|<discontinuation>      | 0 to 4294967295 [seconds] (if 0 we don't care about discontinuation) |
 |<limitH>               | Higher alarm limit (integer from -128 to +127) |
 |<limitL>               | Lower alarm limit (integer from -128 to +127) |
 |<mode>                 | 0 [disable] or 1 [enable]                   |
-|<recess>               | 0 to 180 [seconds]                          |
+|<recess>               | 0 to 65534 [seconds] (~18H) (if 0 we don't care about check sensors alarms) |
 |<resolution>           | decimal resolution (0->0.5, 1->0.25, 2->0.125 and 3->0.0625) |
 |<suid>                 | alias of iButton on 8 char ['0-9'-'A-Z'-'a-z'] like 0A0b0009 |
 |<timestamp>            | 0 to 9'999'999'999 [seconds since 1.1.1970] |
+|<timezone>             | -1200 to +1400 |
+===== Return Code (HEX) =====
+^ Code ^ Transmission ^ Functions ^
+|  67  | ERROR_OPEN            | |
+|  68  | ERROR_SHORTGND           | |
+|  69  | ERROR_SHORTVCC           | |
 ===== Configuration Files (Micro-SD) =====
@@ Line 69: / Line 81: @@
 First line:
-^ Field Name      ^ Description                                  ^ Example    ^
+^ Field Name      ^ Description                                  ^ Example          ^
-| timestamp       | The timestamp of the time when the NiX start | 1400578529 |
+| timestamp       | The timestamp of the time when the NiX start | 1400578529       |
-| slave address   | SID of the slave                             | 21EAF5320000000E |
+| slave address   | SID of NiX                                   | 271A2100000000F3 |
+| general status  | Last general status of NiX before the start (in hex format) | 00 |
 After:
@@ Line 79: / Line 92: @@
 <file log ACTIVITY.#>
-	Slave ID: 1
+1424700000	Slave ID: 2712213200000013	General status: 00
 1424708939	Timeout begin
 1424708939	Alarm on device 281006FF01000099 alias qwertzui
@@ Line 97: / Line 110: @@
 <file txt CONFIG.TXT>
-ADDRESS	1
 BAUDRATE	9600
 BUZZER	0
@@ Line 135: / Line 147: @@
 ==== Temperatures Files ====
-These files contain the temperatures read each scan rate when the NiX1 is in timeout.
+These files contain the temperatures read each scan rate when the NiX1 is in timeout and temperatures read when the master make a query value.
 The suid is the name of the file and the extension is the day of the year (ex: 01010101.237).
 august is the 237 day of year.